GE Profile™ ClearView™ Window Air Conditioner Installation

Today we're going to show you how to install the GE ProfileTM ClearViewTM Smart Window Air Conditioner. Register your product and connect your product to Wi-Fi. This video will provide 8 easy-follow step-by-step instructions to properly install the air conditioner. In addition to the product inside the box, you'll find the necessary installation materials. Please doublecheck that you have each one for beginning installation. Register your product by either scanning the QR code on the product registration card or the rating label on the product. Another easy option is to register online at Gepairs.com, Forward Slash Register, confirm you have the correct size window air conditioner for your room and window size. These instructions are for a standard double-hung window.

You will need to modify them for other types of windows. If your interior window stool or trim sticks out greater than halfinch, no foam spacers are needed. If your interior window stool or trim does not stick out greater than halfinch, two foam spacers are needed. Measure the width of the window opening and mark the center of the opening. Center the foam mounting support in the window opening. Remove adhesive backing and install the necessary amount of foam mounting supports needed to raise the unit above the window ledge.

How to Install a Side Panel Chassis

Measure your window depth and use the table below to determine the necessary chaseway position. After determining the appropriate chaseway position, remove the four locking screws that hold the chaseway in place. Pull the chaseway to the position needed based on your window depth. Place the tab of the side panel bracket into the slot on the chaseway to hold the position. Now install the four screws back into place to lock in the chaseway. It is recommended that two people lift the unit in place into the window. Be careful not to pinch your fingers at the bottom of the chaseway.

How to Install a Window Wedge

Now reach through the window opening and adjust the supports until the unit is secure against the outside wall. Check that the unit is level from front to back and side to side. Once level and secure, reach back through the window and tighten the lockingnut on the adjustable supports to secure everything in place. Now that the unit is secure, we will attach the side panels, close the window, and draw a line where the front edge of the window meets the top of the unit. raise the window back up. Remove the adhesive backing from the side panel brackets and place them onto the unit so that the front edges are lined up with the line you just drew. Now measure the gaps from the side of the unit to the ends of the window and cut the foam side panels to size.

Slide the foam side panels into place within the side panel brackets and ensure the gap to the end of the window is completely sealed. If the panels stick above the chaseway, mark and cut it accordingly. The foam side panels must be flush with the top of the unit. The next step is to cut the adhesive weather stripping foam to the width of the window. Peel off the backing and lay the foam across the width of the window over the unit and side panels following the line drawn with the pencil. After laying the foam down, close the window on top of it. Our last step is to install the window wedge, and sash lock and foam top windowket.

The window wedge is supplied to provide easy access to open the window when desired. It's primarily a convenience option and is not meant to be used for security. For additional security, a sash lock is provided. Attach the sash lock to the window side jam with one Type B screw. Now stuff the foam top window (ketket) between the glass and window to prevent air and insects from getting in the room. The foam may need to be cut to fit depending on the window wedge position.

GE Profile ClearView Smart Window Air Conditioner

Plug into a 3-prong (115 volt) outlet and turn on the air conditioner. You have now completed installation of your GE Profile ClearView Smart Window Air Conditioner. Please note that it's important to clean the air and water filters every 250 hours for proper maintenance. This is an easy process. As shown here, the light will flash on the control panel, let you know it's time to clean the filter. Please refer to the installation guide for additional questions and troubleshooting. To enjoy the many benefits of the smart features of this product, it must be connected. Follow the instructions on the included Smart HQ Guide to connect your unit and begin monitoring and controlling your air conditioner from anywhere. Visit GeAppliances.com and click on Smart Appliances to learn more.

Conclusion

This video will provide 8 easy-follow step-by-step instructions to properly install the air conditioner. In addition to the product inside the box, you'll find the necessary installation materials. Register your product and connect your product to Wi-Fi. These instructions are for a standard double-hung window. You will need to modify them for other types of windows. If your interior window stool or trim sticks out greater than halfinch, no foam spacers are needed. Measure the width of the window opening and mark the center of the opening.